Learning How to Lay Ceramic Floor Tile the Right Way

Raring to start working on your own ceramic floor tile project? Get ready to learn the basics of how to lay ceramic floor tile right here and make that beautiful ceramic tile floor that you and your family have always wanted! So, get your tiling tools ready, put on your safety goggles and let's do some tiling!

Most tiling jobs start with a well-prepared subfloor. As you learn more about how to lay ceramic floor tile, you will find out about the three general types of floors that tile installers may often work with. Such information will help you alot along the way.

Generally, you will encounter three types of subfloors: Vinyl, plywood, and the concrete floors. Installing ceramic tile directly to vinyl or linoleum floors (or subfloor surfaces) should be avoided at all cost. Your vinyl or linoleum flooring may contain asbestos fibers and should be tested first before you try removing it. If your vinyl floor covering does not contain asbestos fibers, a general recommendation on how to lay ceramic floor tile is to rough-sand, or scarify, the vinyl floor surface to provide your tiling mortar a better grip. Use a latex modified thinset mortar to install your ceramic tiles over your vinyl subfloor.

Working over plywood subfloors can be very tricky, as well. Like vinyl floor surfaces, it is not advisable to install your ceramic tiles directly on to your plywood floor surface. Plywood flooring usually has a smooth surface, and easily warps when exposed to heat or moisture. Be sure that the wood is at least 1 and 1/8 inches thick and is reinforced and supported by an equally strong underlayment. Otherwise, your ceramic tiles will dislodge easily, or worse, break and need replacing. Plywood panel edges must be installed about one-fourth of an inch away from perimeter walls and door jambs, and fixtures and cabinetry. These are expansion gaps and should not be bridged with tiling mortar. To prevent moisture from damaging the plywood subfloor, use a waterproofing sealant or caulk over your plywood subsurface.

Concrete floors are the most ideal subfloor surface to work with. But before you start tiling over the subfloor surface, it must be cleaned thoroughly. Paint, adhesives, fillers or levelers, sealers, and chemically treated cement substrates are unsuitable surfaces fpr ceramic tile installations. Remove these by using non-chemical methods. For dust and other debris, sweep and then mop your concrete subfloor surface using only clean water. Allow the surface completely before you start working on it. Generally, smooth concrete surfaces are difficult to work with as the tiling mortar may not grip and hold. Consequently, your ceramic floor tiles may be in danger in dislodging. Smooth concrete surfaces must be rough sanded, scarified, or etched to allow the tiling mortar some grip.

Another important aspect about how to lay ceramic floor tile is to always check for cracks and debris. Repair as many of the cracks as you can. If you see cracks that are too large to repair, replace the floor section where they are found with new concrete. Concrete may need to set (or dry) for at least twenty-four hours before you can start tiling over it. Lastly, get out your carpenter's level and check for any dips or humps on the concrete subfloor surface. If you find any, you may use a cement-based floor level to fill in the dips and smoothen over the humps. This will help to keep your finished ceramic tile floor level and minimize dislodging, or tile breakage.

Let it dry or set properly. This is the key step you need to keep in mind about how to lay ceramic floor tile flooring. There are three setting periods: The first is right after you have placed your ceramic tiles with thin set mortar and bonded them to your subfloor. The second is after after putting in your tiling grout (before putting on the sealant). These setting periods last overnight, at the very least, to twenty-four hours, at the most. Your sealant has dried, you are done!

So when you work on your own ceramic tile project, always remember how to lay ceramic floor tile properly by knowing how to work with your subfloor surfaces. Learning how to lay ceramic floor tile is also both a great way both to learn a new hobby, and a home improvement skill. Just remember to keep a safe working environment, not to rush things (especially during setting periods), and try to work with at buddy. Better yet, get your friends over and help.

Learn how to lay ceramic floor tile on your bathroom or kitchen. Get your ceramic tile installation instructions online.

Tags : PorterCable FR350A Lamps Buying Guide Bar Stools Home Outlet Mall

Continuar leyendo

Ocultar articulo

How To Remove Black Mold From Concrete And Keep Your Basement Mold-Free

Lots of homeowners find out they have an uninvited guest shacking up in their basement. Ever seen little white fuzzy stuff on your concrete basement floor?

Mold on concrete can take many forms. Concrete is a porous substance, and your basement floor gets a lot of moisture from the ground underneath it.

Usually, concrete foundations have a moisture barrier. But, in some cases the moisture barrier is old or damaged, or it may not have been properly installed.

In arid places like Southern California, Arizona and high altitudes, you may not have a moisture barrier built into your home. You usually don't need it, but if you have a heavy rain or a spell of humid weather, you're likely to get that nasty mold growing on your concrete floors.

If you have mold growing on basement tiles or under basement carpeting, the cause may be the concrete underneath. No matter what your mold problem, you have to remove it from your concrete.

A Little Bleach And Elbow Grease

If you've got a little mold growing on your concrete surfaces, it's easy enough to clean up. For little bits of mold here on there, use a solution of water and bleach. 4 parts water to 1 part bleach is usually the recommended formula. You can also find cleaning products designed specifically for mold removal.

Scrub at the moldy spots with your bleach and water until it's gone. Be careful - that bleach is dangerous stuff. Make sure you have some good rubber gloves and be careful that the bleach doesn't come into contact with anything else.

Seal It Up

If you have more serious mold problems and a good scrubbing won't get rid of it, you might try sealing the cracks. Chances are, the appearance of mold on your concrete surfaces is a symptom of a bigger structural problem in your home. There may be cracks in the concrete or walls that allow moisture to come into the house.

Go to the hardware store and look for a waterproofing compound made for this specific purpose. If you're totally unsure, talk to the clerk and explain your problem. What you want is something especially designed to seal up cracks in your concrete and walls. The compound will come with detailed instructions on how to use it.

Call The Contractor

If you have water wicking up from under your foundation into the concrete, you've got a much bigger problem. You may need to call a professional.

What you'll need to do is take off all the flooring so the original concrete is exposed. This is something you can probably do yourself, but you should make sure to keep yourself safe. Any time you're dealing with mold, make sure you have good gloves and a mask, and make sure that the mold doesn't get into any other parts of the house. Even if you're working in the basement, make sure you have some ventilation going.

Now, you'll need to have a new top layer of concrete poured. It has to be at least one inch thick. Make sure that the new cement is mixed with a waterproofing compound that will keep down its moisture level.

This is a big job and most of us would have to call a contractor. Check your local yellow pages.

presentations Personal training

Continuar leyendo

Ocultar articulo

Learning how to Lay Ceramic Floor Tile the Right Way

Raring to start working on your own ceramic tile project? Get ready, the basics of how to lay ceramic tiles here and make the beautiful ceramic tiles, have wanted to learn you and your family forever! So, get your tiling tools ready to put on your safety goggles and we will discuss some tiles!

Most tiling jobs start with a well prepared surface. To learn more about learning how Laying ceramic tiles, you'll be on the three types of soilsTilers that often work. This information will help you a lot on the road.

In general, you are three types of surfaces: vinyl, plywood meeting, and the concrete.) Should install ceramic tile directly to vinyl or linoleum (or subfloor surfaces to be avoided at all costs. Your vinyl or linoleum flooring may contain asbestos fibers and should first be checked before trying to remove. If your not contain vinyl flooringAsbestos fibers, a general recommendation, as is put ceramic tiles, coarse sand, or scarify, linoleum floor to the surface, enter your tile mortar a better grip. Use a latex thinset mortar to install your tiles over your vinyl subfloor.

Working over plywood subfloors can be very difficult, as well. Floor coverings such as vinyl, it is not advisable to install your tiles directly on to your plywood floor space. Plywood flooring usually a smooth surface;and slightly distorted when exposed to heat or humidity. Make sure the timber is at least 1 and 1 / 8 inch thick, and reinforced and supported by an equally strong underbody. Otherwise, your tile is easy to distribute, or worse, break and need replacing. Plywood edges are approximately one quarter of the tariff will be installed away from walls and door jambs, and fixtures and furniture. These are expansion gaps and should not be bridged with tiling mortar. To prevent moistureDamage to the subfloor plywood, sealed with a sealant or caulk over your plywood substrate.

Concrete floors are the ideal working ground surface. But before you tile on the surface of the subfloor, it must be thoroughly cleaned. Paint, adhesives, fillers, graders, seals and chemically treated cement substrates are unsuitable surfaces fpr ceramic tile installations. Remove them by using non-chemical methods. For dust and other contaminants, and sweepmop your concrete subfloor surface with clean water. Let the surface completely before you begin working on it. In general, smooth concrete surfaces are difficult to work in tile grout should not hold hands. Consequently, your ceramic tiles can displace in danger. Smooth concrete surfaces must be rough sanded, scarified, or etched to allow the tile to mortar some grip.

Another important aspect about how to lay ceramic tileis to always check for cracks and dirt. Repair cracks as many as you can. If you see cracks that are too large to repair, replace the bottom plate when she found with new concrete. Concrete You may need (or dry) at least twenty-four hours before you can start tiling over it. Finally, you get your carpenter's level and check for any dips or bumps on the concrete subfloor surface. If you find you have a cement-based flooring in the fillingDips and smooth over the humps. This will help to keep your finished ceramic tiles level and minimize crowd out, or breaking of tiles.

Let it dry and set properly. This is the crucial step you take hold as the ceramic tile floor was too. There are three setting periods: The first is right after you have set your tile with thin set mortar and bonded them to your base. The second, after having in your tile grout (before putting theSealing). These setting periods last night, at least, to twenty-four hours at most. Your sealant has dried, you're done!

So, if you work on your own ceramic tile project, always remember to know how to properly ceramic tiles, as you do with your work underbody surfaces. Learning how to lay ceramic tile is also a good opportunity both for both a new hobby to learn, and a home improvement skill. Please note, keeping a safe working environment, not to rush(may be extended, especially during the setting), and try to work on buddy. Even better would be to get your friends about using.

Circular Saw, Saw Blade how make money presentations

Continuar leyendo

Ocultar articulo

Ask This Old House 7x17 (3 / 3) staining a deck / prevention sewage backups

Ask This Old House 7x17 (3 / 3) staining a deck / prevention sewage backups Downloads for this can be found here: diytvfan.blogspot.com The official site can be found here: www.thisoldhouse.com



http://www.youtube.com/watch?v=iShzTGvHGPM&hl=en

Weekly rentals use stock

Continuar leyendo

Ocultar articulo

Pergo Laminate Flooring - Learning how to build a DIY Pergo Flooring Installation

Pergo Laminate Flooring is one of the giants in the laminate parquet industry. The floors are designed for DIYers restored, so questions about the installation of laminate flooring in the context abound. Pergo, Harmonics, Armstrong laminate and similar products are of happy, threw hand-rubbing for the first time home remodel. In an average-sized floor can be ready for immediate use and admire within a day - just imagine all the compliments from somewhatGreen-around-the-gills neighbors ...

The days of the struggle against the messy, sticky, glued laminate flooring is suitable for long over, thanks to areas such as Pergo laminate flooring laminate flooring planks. The unique tongue and groove construction Pergo floors, you simply click together for a perfect finish. This is one of the most gratifying do it yourself deal with jobs, as progress is measurable and the end result is quite spectacular.

Installing Pergo Flooring is recommended over existing flooring?

TheBeauty of Pergo laminate is that it can be directly on ceramic, vinyl, tile or real wood floors installed, you save yourself the trouble of ripping an old first floor. Make sure that the floor clean, smooth and carefully sand down and moguls reached joints. Carpet care must be taken, however. It is always recommended to do fittings of cabinets or closets first before tackling your flooring project. Real hardwood installed over a concrete base andneeded before a Pergo installation will be removed.

Do I Need expansion space around the perimeter of my Pergo Flooring Installation?

Pergo laminate is a floating floor product, meaning that it is not permanently fixed to the sub-base. These areas expand and contract due to changes in humidity and temperature. It is therefore important to leave a 1 / 4 "expansion space between the flooring planks and the adjacent walls or cupboards. If you do not,You have unsightly buckling floors. The Pergo floor moldings are used to hide these spaces after installation and to ensure a professional finish. Use spacers to even keep your distance. If you are fighting a very large area must be increased by the expansion space.

Pergo is laminate also have a hollow sound, when used?

The sound depends largely on the surface layer and the thickness of the laminate flooring installation. OneWay to get around this is to install a solid subfloor and resin polyethylene film underneath your Pergo laminate planks. This is a very effective technique to use if you want to mute the sound. This protective layer also acts as a vapor barrier, extends the life of the flooring. Take a look at Pergo SilentStep foam or foam Soundbloc and Moisturbloc vapor barrier. By adding this, a damping layer can also ensure a more comfortable, soft ground under my feet. WhenSubstrate is wood, not a vapor barrier in place before the installation of Pergo laminate.

Can I Pergo immediately after my purchase?

To get used on the safe side, your Pergo floor by leaving the cartons in the room where she is to be installed for a period of 49 to 96 hours. This precaution will give you a floor that fell is still his place, instead of an ugly bruises disaster area.

Can I PergoLaminate in a bathroom or kitchen?

Pergo laminate surface is highly water repellent, so that the boards can be used in high humidity areas like bathrooms and kitchens. Trimming in these areas must, however, the expansion of areas with Pergo Sealant or a similar powdery mildew-resistant silicone product to be closed before installing or injection molding. The same should be done where the planks were cut to make room for cupboards or a dishwasher. Some experts also recommend sealing theJoints by using glue. Check with your supplier about the satisfactory installation. Despite its resistance to water Pergo laminate are not made to treat standing water.

Can I Pergo on stairs?

Pergo flooring is suitable for stairs. Steps are finished with Pergo Stair Nosing. The nosing is adhered with a quality construction adhesive and finishing screws. A stair application is the only time that the floating floor concept is the PergoReplaced with a glued end product.

How can I ensure a professional finish installing Pergo laminate?

An extensive range of color-coordinated transition moldings are set for an elegant and stylish Finish to your flooring project. T-moldings are used in the doorways, while end moldings and doors and are used for baths and basins. If you need to go from an elevated Pergo flooring area to a lower hard surface such as vinyl, you would choose a hard surfaceReducer.

Regard! I Have A Nick In My Pergo laminate! What now?

No problem. The people of Pergo clear that this is an accident is inevitable, is a lively household. Therefore, make sure that you have access to Pergo Finishing Putty. Simply neaten the edges of the chipped with a small knife sure that the area clean and fill the hole with putty. A spatula is a clean surface and the rest is simply wiped away with a clean cloth. Plank replacements are alsopossible if a major repair is needed.

With a gleaming Pergo Presto or Pergo American Cottage transfer your living room will be transformed into a fold less elegant lady. Pergo laminate was carrying out plastic surgery on Properties on year. It's time to let go of that tattered carpet ...

My Links : linux web hosting domain name registration casino gambling

Continuar leyendo

Ocultar articulo